EX100/200 Insert Electromagnetic Flow Meter

Fixed depth electromagnetic insertion flow meters 
Seametrics Insertion Flow Meter
Electromagnetic Insertion Flow Meter

GENERAL INFORMATION

The complete lack of moving parts of the EX100/200 Series seametrics insertion flow sensor is the source of its reliability. Brass and stainless steel models withstand a variety of temperature, pressure, and chemical conditions. The EX-Series has no rotor to stop turning in dirty water and there are no bearings to wear out. Like all magmeters, when used in chemical injection applications, these meters should be installed upstream of the chemical line (or far enough downstream to allow complete mixing of fluids before the meter).

A rapidly reversing magnetic field is produced in the lower housing. As the fluid moves through this field, a voltage is generated that is measured and translated into a frequency signal proportional to flow rate. This square wave signal can be sent directly to a PLC or other control or can be converted using any of the Seametrics family of indicators and converters.

A modular system of electronics can be attached directly to the flow sensor or remotely mounted. The Seametrics FT420 provides full indication of rate and total, plus 4-20 mA output. The AO55 provides blind 4-20 mA output, and the DL76 is a battery-powered data logger.

Features :

• Depth adjustable sensors
• EX101 fits any 1-1/2" pipe fitting (standard saddle, for instance) and adjusts to pipe sizes 3-10"
• EX201 adjusts to pipe sizes 10-48"
• Meter extends only about 1/8 of pipe diameter, minimizing potential for clogging with debris
• Accept SeaMetrics modules for rate and total indication, 4-20 mA conversion, data logging, and flow switching
• Alternatively, signal can be sent directly to a PLC or other control
• Available in brass or 316 stainless steel
• Immersibility and reverse flow output available

The adapter fitting of the EX sensor is standard male NPT, and can be directly threaded into ordinary saddles or threaded weld fittings. The EX115 and 215 include an isolation valve, allowing hot-tap installation, or installation and removal under pressure; a bronze ball valve is standard, with a 316 stainless steel valve option if needed. Reverse flow output and immersibility are optional.

Adjustable Depth EX 100 Electromagnetic Flow Sensor Specifications

• Accuracy: 1% of full scale
• Output: Square wave pulse, opto isolated, 500 Hz @ 20 ft/sec
• Bi-Directional: Direction output, opto isolated
• Empty Pipe Detection: Flow defaults to zero
• Flow Range: 0.2 - 20 ft/sec (.06 - 6.09 m/sec)
• Maximum Pipe Pressure: 200 PSI (13.8 bar)
• Temperature: Ambient 0º – 180º F (-17 - 82º C) • Fluid 32º – 212º F (0º - 100º C)
• Minimum Conductivity: 20 microsiemens/cm
• Power: 12 - 24 Vdc, 250 mA
• Installation Fitting Size: 1-1/2” Male NPT

Materials:

• Mechanical: 316 SS/Brass
• Electrodes: Hastelloy
• Electrode plate: PVDF
• Housing Cast: powder-coated aluminum
• O-rings: EPDM

Adjustable Depth Electromagnetic Flow Sensor Options

• EX101B Adjustable Depth Electromagnetic Flow Sensor
• Brass Insertion Electromagnetic Flow Sensor, for 3" to 10" pipe diameter.
• EX101S Adjustable Depth Electromagnetic Flow Sensor
• Stainless Steel Insertion Electromagnetic Flow Sensor, for 3" to 10" pipe diameter.
• EX201B Adjustable Depth Electromagnetic Flow Sensor
• Brass Insertion Electromagnetic Flow Sensor, for 10" to 48" pipe diameter.
• EX201S Adjustable Depth Electromagnetic Flow Sensor
• Stainless Steel Insertion Electromagnetic Flow Sensor, for 10" to 48" pipe diameter.

Optional Output Displays/Converters

• Meter mounted displays/converters include 18 feet of cable.
• FT420M/FT420W Pulse & 4-20mA Output Display
• Requires 12-24VDC power.  Specify meter or wall mounted.
• AO55M/AO55W Blind 4-20ma Converter
• Requires 24-36VDC power.  Specify meter or wall mounted.